Hardware: Hive Interface Board 1.0

From HiveTool
Revision as of 10:26, 19 August 2018 by Paul (talk | contribs) (→‎Introduction)
Jump to: navigation, search


Introduction

The HiveTool Hive Interface board was designed using gEDA schematic capture and Printed Circuit Board (PCB) layout software. The software, schematics, pcb layout and Gerber files are included on the latest imagein /home/hardware.

There are two different connector versions: version 0.2 and versions 0.3 and greater. Unplug the HX711 to read the version. List of changes between version 0.3 and 1.0.

Version 1.0

Schematics

Version 1.0 (pdf)

Analog Sensor Inputs

Load Cell Inputs

Analog to digital conversion is done by the HX711. It plugs into Hive Interface headers H8 and H9 in the lower right corner.


Digital Sensor Inputs

Hive Interface Board 0.3 and 1.0 Digital Sensor Ports

This is the default sensor configuration but others are possible. The I2C bus communicates with the TSL2195 lux sensor, the DS3231 RTC and the BME680 Temp/Humidity/Pressure/Gas sensor.

Hive Interface Board Digital Sensor Inputs
Name/Purpose Interface Header Pins Sensors
Lux I2C 3, 5 TSL2561 TSL2591 BME680
Hive Temp/RH GPIO/1-Wire DHT:13 1-Wire:11 DHT11 DHT22 DS18B20
Ambient Temp/RH GPIO/1-Wire DHT:15 1-Wire:11 DHT11 DHT22 DS18B20
Rain GPIO/1-Wire Rain:22 1-Wire:11 Tipping bucket rain gage and/orDS18B20


Raspberry Pi default Interfaces
Interface Header Pin Broadcom GPIO Pins RPi GPIO Pins
I2C 3, 5 2, 3 8, 9
1-Wire 11 17 0


Real Time Clock

DS3231 Real Time Clock

Plugs into header H2 located on the upper right.

More details on the RTC

Serial Console

H4 upper left.

GPIO List

Handy list of Pi GPIO pin numbers, names and purposes.







Version 1.0 of the Hive Interface Board will begin testing. As suggested by the 1.0 designation, this is considered to be "done" and should be the final release of this design.

Changes

  • Added Real Time Clock (RTC) support so DS3231 will plug into the I2C header H2 without modification.
  • Changed 1-Wire connection to Pi's default 1-Wire GPIO by swapping GPIO pin for LED from pin 7 (default 1-wire) to pin 11.
  • Added Chip Enable signal to SPI bus signals on H7.
  • Increased hole size for blue 12 VDC power connector from .038" to .042".

Features

  • Plug and Play - all the sensors plug in.
  • 12 VDC power supply with battery voltage monitoring
  • Supports
    • HX711 24 bit ADC and 4 load cells in parallel.
    • two DHT22 temperature/humidity sensors.
    • unlimited DS18B20 1-Wire temperature sensors (or other 1-Wire devices).
    • TSL2591 Lux sensor
    • Rain Gauge


Plug and Play. Telco RJ14 (6P4C) connectors are used for all sensors. These are gold plated, reliable, self wiping, inexpensive, readily available, crimp on with an inexpensive crimping tool, lock in place (latch) and as anyone who has tripped over a phone cord can attest, very strong.

Two different power supplies are optional. These are 12 to 5 volt step down highly efficient switching regulators.

The interface board and software works with the A+. B+, Pi2 and Pi3 models. The board will work with the original A or B if a 26 pin header extension is used although the lack of mounting holes in the original Pi is a problem.


This board was designed on the Pi using the gEDA programs gschem and pcb. The programs, schematic and layout files are included on the latest image.

Retrieved from "http://18.212.38.72/index.php?title=Hardware:_Hive_Interface_Board_1.0&oldid=3667"