Difference between revisions of "Interface the HX711 to Pi"
| Line 7: | Line 7: | ||
You will need a 1x4 female header ([http://www.amazon.com/Gino-2-54mm-Straight-Single-Headers/dp/B00899WQ6U/ref=sr_1_1?s=electronics&ie=UTF8&qid=1397881924&sr=1-1&keywords=headers 2.54mm Pitch Straight Single Row PCB Female Pin Headers]) and [http://www.phidgets.com/products.php?category=34&product_id=3135_0 load cells]. | You will need a 1x4 female header ([http://www.amazon.com/Gino-2-54mm-Straight-Single-Headers/dp/B00899WQ6U/ref=sr_1_1?s=electronics&ie=UTF8&qid=1397881924&sr=1-1&keywords=headers 2.54mm Pitch Straight Single Row PCB Female Pin Headers]) and [http://www.phidgets.com/products.php?category=34&product_id=3135_0 load cells]. | ||
| − | #Order the board for $6.99 on [http://www.ebay.com/itm/Weighing-Sensor-AD-Module-Dual-channel-24-bit-a-d-Conversion-HX711-Shieding-/400460838550 Ebay]<br>[http://www.ebay.com/itm/ | + | #Order the board for $6.99 on [http://www.ebay.com/itm/Weighing-Sensor-AD-Module-Dual-channel-24-bit-a-d-Conversion-HX711-Shieding-/400460838550 Ebay]<br>[http://www.ebay.com/itm/Weighing-Sensor-AD-Module-Dual-channel-24-bit-a-d-Conversion-HX711-Shieding-/400460838550 This one] for $2.19 should work, too. |
#Download the software from gitHub <br> git clone https://github.com/ggurov/hx711 | #Download the software from gitHub <br> git clone https://github.com/ggurov/hx711 | ||
#Solder a 1x4 straight female header in P5 on Pi (bottom side of board) and a 1x4 male header on the DCT board | #Solder a 1x4 straight female header in P5 on Pi (bottom side of board) and a 1x4 male header on the DCT board | ||
| Line 45: | Line 45: | ||
http://hivetool.org/w/images/d/d2/Hx711_english.pdf | http://hivetool.org/w/images/d/d2/Hx711_english.pdf | ||
==Load Cell Spec Sheet== | ==Load Cell Spec Sheet== | ||
| − | [http://www.phidgets.com/products.php?category=34&product_id=3135_0 | + | [[http://www.phidgets.com/products.php?category=34&product_id=3135_0]] |
Revision as of 15:05, 22 April 2014
Building a Raspberry based electronic scale using the DCT Electronic HX711 board is as easy as Pi!
The DCT board comes with two sets of male headers, straight and right angle, and a metal shield.
You will need a 1x4 female header (2.54mm Pitch Straight Single Row PCB Female Pin Headers) and load cells.
- Order the board for $6.99 on Ebay
This one for $2.19 should work, too. - Download the software from gitHub
git clone https://github.com/ggurov/hx711 - Solder a 1x4 straight female header in P5 on Pi (bottom side of board) and a 1x4 male header on the DCT board
- Solder the load cells to the DCT board.
- Plug the DTC board into the Pi.
- Change the GPIO pins in hx711.c from 30 and 31 to 28 and 30. This way they are all on one side of P5:
#define CLOCK_PIN 30 #define DATA_PIN 28
| P5 | Pi | HX711 |
|---|---|---|
| P5-1 | +5 | Vcc |
| P5-3 | GPIO28 | DO/RX |
| P5-5 | GPIO30 | CK/TX |
| P5-7 | Ground | GND |
Calibration
HX711 Spec Sheet
http://hivetool.org/w/images/d/d2/Hx711_english.pdf
Load Cell Spec Sheet
[[1]]
