Difference between revisions of "Change: Hive Interface 0.3"
(→Change pins on H2 I2C so Real Time Clockk (RTC) will plug in.) |
(→Change GPIO pin for LED from pin 7 (default 1-wire) to pin 11.) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
==Change GPIO pin for LED from pin 7 (default 1-wire) to pin 11.== | ==Change GPIO pin for LED from pin 7 (default 1-wire) to pin 11.== | ||
| + | This means that dad7 (data acquisition daemon that flashes the LED and reads the rain gauge) won't flash the LED. Need dad8 version. Maybe set LED GPIO pins with command line options. | ||
==Add Chip Select to SPI (GPIO 10 SPI0_CE0) to H7.== | ==Add Chip Select to SPI (GPIO 10 SPI0_CE0) to H7.== | ||
| Line 58: | Line 59: | ||
|} | |} | ||
| − | ==Change pins on H2 I2C so [[Real Time Clock RTC | Real Time | + | ==Change pins on H2 I2C so [[Real Time Clock RTC | Real Time Clock (RTC)]] will plug in.== |
*Remove +5 VDC from Pin 1. | *Remove +5 VDC from Pin 1. | ||
| Line 79: | Line 80: | ||
|- | |- | ||
| 3 | | 3 | ||
| − | | I2C | + | | I2C SDA |
|- | |- | ||
| 4 | | 4 | ||
| − | | I2C | + | | I2C SCL |
|- | |- | ||
| 5 | | 5 | ||
| Line 99: | Line 100: | ||
|- | |- | ||
| 2 | | 2 | ||
| − | | I2C | + | | I2C SCA |
|- | |- | ||
| 3 | | 3 | ||
| − | | I2C | + | | I2C SCL |
|- | |- | ||
| 4 | | 4 | ||
Latest revision as of 03:02, 13 November 2018
Contents
Increase hole size for blue 12 VDC power connector.
Increased from .038" to .042".
Change GPIO pin for LED from pin 7 (default 1-wire) to pin 11.
This means that dad7 (data acquisition daemon that flashes the LED and reads the rain gauge) won't flash the LED. Need dad8 version. Maybe set LED GPIO pins with command line options.
Add Chip Select to SPI (GPIO 10 SPI0_CE0) to H7.
This is for the AD7124-8 Eval Board. Need Chip Enable (CE) to frame the word.
Hive Interface 0.3
| H7 SPI ver 0.3 | |
|---|---|
| Pin | Signal |
| 1 | +3.3 |
| 2 | GPIO 14 SPIO CLK |
| 3 | GPIO 13 SPIO MISO |
| 4 | GPIO 12 SPIO MOSI |
| 5 | Ground |
New:
| H7 SPI ver 0.5 | |
|---|---|
| Pin | Signal |
| 1 | +3.3 |
| 2 | GPIO 14 SPIO CLK |
| 3 | GPIO 13 SPIO MISO |
| 4 | GPIO 12 SPIO MOSI |
| 5 | GPIO 10 SPIO CE0 |
| 6 | Ground |
Change pins on H2 I2C so Real Time Clock (RTC) will plug in.
- Remove +5 VDC from Pin 1.
- Make Pin 4 No Connect (NC)
This will allow the DS3231 to plug into header H2 without modifying the Hive Interface board.
Hive Interface 0.3:
| H2 I2C Bus ver 0.3 | |
|---|---|
| Pin | Signal |
| 1 | +5 |
| 2 | +3.3 |
| 3 | I2C SDA |
| 4 | I2C SCL |
| 5 | Ground |
New:
| H2 I2C Bus ver 0.5 | |
|---|---|
| Pin | Signal |
| 1 | +3.3 |
| 2 | I2C SCA |
| 3 | I2C SCL |
| 4 | NC |
| 5 | Ground |
