Hardware: Sensor Wiring

The Developers Kit Raspberry Pi Hive Interface Board uses modular telephone RJ14 (6P4C) connectors for the sensors. Pins 2, 3, 4, and 5 are used.

Eventually, the load cells will be supplied with the connector attached. Cables will be provided for the other sensors.

These instructions are for developers that use the Dev Kit Raspberry Pi Hive Interface board versions 0.1 - 0.3.

The Registered Jack (RJ) series connectors install using an inexpensive crimping tool.

RJ Connectors

Crimp on Registered Jack (RJ) plugs are insulation displacement connectors (IDC) that pierce the insulation on the wire, forming a gas tight joint. Some RJ connectors are designed to take round cable, some flat, some both. Some are designed for solid wire, some for stranded, some for both.

The male connectors are called plugs. The female connectors are called jacks. They are designated by the number of positions (P) and the number of contacts (C) that are populated. We are currently using 6P4C (six position, four contact) plugs and jacks.

For a detail description, see Registered Jack on Wikipedia.

Load Cells

Load Cell Wiring
RJ14 Pin	Color	HX711	Description
2	Red	OUT+	Excitation voltage from HX711 voltage regulator
3	White	A-	A/D channel A negative input
4	Green	A+	A/D channel A positive input
5	Black	GND	Analog ground

1. Remove any heat shrink from the load cell cable.
2. Cut off the drain wire.
3. Spread out the four wires and arrange them in Red, White, Green, Black order.
4. Gently flatten the cable with a pair of pliers.
5. Evenly trim the wires so they extend approximately 1/4 inch past the jacket.
6. Orient the RJ14 connector so the latch tab is up.
7. Insert the wires all the way into the RJ14 connector, making sure that the wires are in the right order.
8. Inspect the wires and connector with a magnifier. Make sure the outer jacket is past the strain relief and each wire is all the way to the end of the connector.
9. If the wires do not extend the full length of the connector, or the jacket does not go past the strain relief, remove the wire and trim a little of the jacket, or shorten the wires.
10. Crimp the connector.

DHT22/AM2302 Temperature and Humidity Sensor

Bare Sensor

DHT22 Wiring
RJ14 Pin	Color	DHT22 Signal	Description
2	Black	+	+3.3VDC supply
3	Red	Out	Pi GPIO
4	Green	No Connect	Not used
5	Yellow	-	Digital ground

Wire type is standard four conductor flat telephone wire.

Jacket color is not important, recommend light color, avoid black.

Telephone wire colors are Black, Red, Green (not used), Yellow.

Crimp the RJ14 connector for normal telephone use.
Consider cutting a 10 or 12' cord in half for two sensors, crimping will be unnecessary

Trouble shooting: Make sure the cable is crimped Black, Red, Green, Yellow and not Yellow, Green, Red, Black.

Wired Sensor

Wired DHT22 WARNING wire color code is different. Red: +5, Black: Ground, Yellow: Signal

The wired sensor is larger and more expensive. It will not fit inside the hive (between the supers) as well as the bare DHT22 sensors.

Wire phone cable Black to DHT22 Red.
Wire phone cable Red to DHT22 Yellow.
Wire phone cable Yellow to DHT22 Black.

Wired DHT22 Wiring
RJ14 Pin	Color	DHT22 Signal	DHT22 Color	Description
2	Black	+	Red	+3.3VDC supply
3	Red	Out	Yellow	Pi GPIO
4	Green	No Connect	Not used
5	Yellow	-	Black	Digital ground

TSL2591 Lux Sensor

TSL2591 Wiring
RJ14 Pin	Color	TSL2591 Signal	Description
2	Black	Vin	+3.3Volt input
3	Red	SDA	Pi GPIO 8 I2C SDA
4	Green	SCL	Pi GPIO 9 I2C SCL
5	Yellow	GND	Digital ground

TSL 2591: 3Vo - not used, Int - not used.
Wire type is standard four conductor flat telephone wire.
Jacket color is not important, recommend light color, avoid black
Wire colors are Black, Red, Green, Yellow.
Crimp the RJ14 connector for normal telephone use.
Consider cutting a 10 or 12' cord in half for two sensors, crimping will be unnecessary

TIP A ping pong ball cut in half makes a weather shield and lens when attached to a flat base using glue.
A small pouch of desiccant attached inside will reduce moisture condensation.
Attach the sensor on top of the hive cover.

Rain Gauge

Uses the "Tipping Bucket" type rain gauge.

Red and Yellow wires.